top of page

FRP Grating, Cable Tray, and Handrail for Offshore Wind Platforms

Oct 15
7 min read

An offshore wind turbine sits in one of the most hostile material environments on earth. Continuous salt spray, permanent high humidity, wind-driven chloride deposition, and restricted access for maintenance define the conditions that every material on the platform must perform in for 25 to 30 years. Steel corrodes. Aluminium pits in chloride-rich conditions. Both conduct electricity in an environment where high-voltage generation equipment is present on the same platform as personnel access structures. FRP grating, cable tray, and handrail systems are specified on offshore wind platforms precisely because they are corrosion-resistant without maintenance, non-conductive without earthing, and light enough to keep dead load within the structural budget of the platform deck. As the UK's offshore wind programme expands toward 50 gigawatts of capacity, the secondary structural specification that goes into each platform is being made for the next three decades of North Sea service.

Published by Reinforce Technology  |  15 October 2026


The UK is the largest offshore wind market in the world. With over 14 gigawatts of installed capacity and a pipeline that extends to 50 gigawatts under the government's Clean Power 2030 commitment, the country is building offshore wind infrastructure at a scale and pace that makes the specification decisions for each new platform matter more than they ever have before. Each turbine foundation, transition piece, and offshore substation carries secondary structural infrastructure: walkway grating, handrail systems, cable management, and access ladders. The materials those structures are made from determine their maintenance requirement, their weight contribution to the platform dead load, their electrical safety profile in proximity to high-voltage generation equipment, and their performance over a 25 to 30-year design life in the North Sea marine environment (IRENA, 2024).

Offshore wind farm walkway over choppy sea, with turbines in the distance under a cloudy bright sky.
FRP grating, handrail, and cable tray on offshore wind turbine platforms and transition pieces: corrosion-resistant to continuous salt spray and chloride deposition without maintenance recoating, non-conductive near high-voltage generation equipment, and 75% lighter than steel, reducing dead loads on platform decks across 25 to 30-year North Sea service lives.

The Offshore Environment and What It Demands of Secondary Structural Materials


The North Sea marine environment subjects offshore structures to corrosion conditions that are among the most aggressive in any industrial application. Salt spray chloride deposition is continuous at turbine height. Humidity at platform level routinely exceeds 90%. Temperature cycling between winter and summer accelerates the mechanical fatigue of surface coatings. Wind-driven water carries chloride ions into every joint, bolt hole, and surface imperfection in metallic secondary structures. Galvanised steel in this environment requires inspection and recoating on a cycle that brings maintenance personnel to the platform at significant cost and with significant exposure to North Sea weather conditions. Stainless steel resists corrosion better than galvanised mild steel but is substantially heavier and, where chloride pitting in crevices occurs, can fail in ways that are difficult to detect during routine inspection (ScienceDirect, 2023).


FRP secondary structures in vinyl ester resin are inherently resistant to the chloride, humidity, and salt spray conditions of the North Sea marine environment. The corrosion resistance is not a surface coating that degrades and requires replacement: it is integral to the resin matrix throughout the full cross-section of the grating panel, cable tray section, or handrail profile. There is no zinc layer to deplete, no passive oxide layer to pit, and no coating system to inspect and reapply. In a maintenance environment where each offshore access event carries a significant cost and a weather dependency, the elimination of corrosion-driven maintenance from the secondary structural programme across a 25 to 30-year asset life is a material specification decision with direct consequences for operational expenditure (IntechOpen, 2022).


FRP Grating on Offshore Wind Platforms


Walkway grating on offshore wind turbine transition pieces and platform decks must carry personnel and equipment loads in a wet, slippery environment while contributing as little dead load as possible to the platform structure. Steel grating at the depths required for standard access platform load ratings is heavy: the dead load of the grating itself is a significant fraction of the total load the platform structure must support. FRP moulded grating at 38x38mm mesh with gritted anti-slip top surface is approximately 75% lighter than steel grating of equivalent depth, and meets the anti-slip performance requirements for offshore access platforms in wet and contaminated conditions.


The gritted top surface of FRP grating, in which abrasive aluminium oxide or silicon carbide aggregate is bonded to the top face during manufacture, provides the high slip resistance required for personnel working in offshore conditions where the walking surface is continuously wet and may carry salt deposits, hydraulic fluid, or lubricant contamination. Because the colour of FRP grating is integral to the resin rather than applied as a coating, safety yellow grating panels on offshore platforms retain their identification colour for the full service life of the installation without the recoating that steel safety-yellow grating would require in the North Sea environment.


FRP Cable Tray for Offshore Wind Electrical Infrastructure


Offshore wind turbines generate electricity at medium voltage and export it through subsea cable systems that connect to the offshore substation and onward to the onshore grid. Within each turbine tower, transition piece, and offshore substation, cable management infrastructure carries high-voltage power cables, control cabling, and fibre-optic signal connections between generation equipment and the export systems. That cable management infrastructure runs in an environment where high-voltage electrical equipment is present at every level.


Steel and aluminium cable tray in this environment requires earthing and bonding in accordance with BS 7671, adding installation complexity and creating conductive structures in proximity to high-voltage equipment. FRP ladder tray and perforated cable tray are non-conductive. They require no earthing or bonding, create no fault current pathway near high-voltage equipment, and deliver corrosion resistance to the salt spray and humidity conditions of the offshore environment without the maintenance recoating that metallic cable containment systems require. For offshore wind operators managing maintenance costs across large turbine arrays over 25 to 30-year asset lives, the combination of maintenance-free corrosion performance and non-conductive electrical safety in a single cable management material is a specification advantage that metallic alternatives cannot match (IET, 2018).


FRP Handrail Systems on Turbine Platforms and Transition Pieces


Handrail systems on offshore wind platforms must comply with the fall protection requirements applicable to offshore working at height, withstand the structural loads imposed by personnel in storm conditions, and perform in the salt spray and chloride deposition environment of the North Sea without the corrosion that degrades metallic handrail systems over multi-year service. Steel handrail on offshore platforms requires galvanising or coating, periodic inspection for corrosion and mechanical damage, and replacement on a cycle that brings personnel to the platform in weather conditions that can be hazardous.


FRP modular handrail systems are assembled from pultruded FRP top rail, mid rail, and upright profiles using snap-fit or bolted connections that require no welding, no hot work permits, and no specialist trades for installation or modification. The profiles are non-conductive, so handrail runs near high-voltage cable routes or electrical enclosures on the turbine platform do not require the clearance assessment that metallic handrail systems trigger. In safety yellow, the colour is integral to the resin throughout the profile cross-section, maintaining the visual identification of safety barriers across the full offshore service life without repainting. On a turbine transition piece or monopile platform, the combination of lightweight installation, non-conductive material, and maintenance-free corrosion performance across 25 to 30 years represents a whole-life cost saving against steel handrail that compounds across every turbine in a large offshore wind array.


Weight, Dead Load, and the Offshore Platform Structural Budget


Offshore wind platform design is governed by weight. Every kilogram of secondary structure added to a transition piece or platform deck is a kilogram of load the primary steel structure must support under wave, wind, and operational loading. Reducing the dead load of secondary structural materials directly benefits the primary structural design, or frees capacity for additional equipment within the platform's weight budget. FRP grating, handrail, and cable tray at equivalent structural performance to steel are collectively 70 to 75% lighter. On a turbine transition piece carrying grating, handrail, and cable management across multiple levels, the aggregate dead load saving of FRP specification versus steel specification is significant, and it applies without compromise to the structural performance or the service life of the secondary structures themselves (IntechOpen, 2022).


Non-Sparking Installation and Modification in Hazardous Areas


Offshore wind turbines contain lubricating oils, hydraulic fluids, and gearbox systems that can create flammable vapour environments in enclosed spaces within the nacelle and tower. During installation and maintenance operations, the cutting and drilling of secondary structural materials on or near the turbine creates a source of ignition if those materials generate sparks on contact with cutting tools or on impact with metallic surfaces. FRP is non-sparking. It can be cut with standard angle grinder or diamond blade tools without generating the metal sparks that steel and aluminium produce, removing one category of ignition risk from installation and maintenance work in potentially flammable environments on offshore wind platforms.


The UK's 50 gigawatt offshore wind programme is specifying secondary structural infrastructure across hundreds of turbine platforms for 25 to 30-year North Sea service lives. FRP grating, cable tray, and handrail systems are the specification that eliminates corrosion maintenance from those structures, removes earthing and bonding complexity from cable management near high-voltage equipment, reduces dead load on platform decks by 75%, and delivers non-sparking material properties for installation and maintenance in enclosed turbine spaces. Reinforce Technology supplies FRP grating, ladder tray, and handrail systems for offshore wind and marine infrastructure across the UK. Contact us to discuss specification for your project.


FRP product selection for offshore wind applications should be confirmed against the specific structural loads, environmental exposure conditions, electrical classification, and fall protection standards applicable to the installation. Resin system suitability for the confirmed chemical and temperature exposure of the specific location should be verified with the manufacturer prior to specification.


References


IET (2018) BS 7671:2018 Requirements for Electrical Installations (IET Wiring Regulations), 18th Edition. Institution of Engineering and Technology, London. [Earthing and bonding requirements for metallic cable containment in proximity to high-voltage equipment; non-conductive cable tray exemption from earthing and bonding obligations; electrical safety requirements for offshore and marine electrical installations].


IntechOpen (2022) 'Fibre-Reinforced Polymer (FRP) in Civil Engineering', in IntechOpen Engineering Series. Available at: https://www.intechopen.com/chapters/84203 [Accessed: 15 October 2026]. [FRP grating 70-75% lighter than steel at equivalent depth; vinyl ester resin corrosion resistance to chloride and marine environments; non-conductive; non-sparking; no maintenance recoating; 25-50 year design life in corrosive marine and offshore environments; dead load reduction on offshore platform structures].


IRENA (2024) Offshore Wind Outlook: UK and North Sea Capacity Projections. International Renewable Energy Agency. Available at: https://www.irena.org/publications/2024/offshore-wind-outlook [Accessed: 15 October 2026]. [UK offshore wind installed capacity exceeding 14 GW; 50 GW target under Clean Power 2030; North Sea expansion pipeline; offshore turbine platform and transition piece infrastructure scale across UK programme].


ScienceDirect (2023) 'Corrosion performance of structural materials in North Sea offshore environments', Corrosion Science, 215, pp. 1-22. Available at: https://www.sciencedirect.com/science/article/pii/S0010938X23003456 [Accessed: 15 October 2026]. [Galvanised steel corrosion rates in continuous salt spray and high-humidity offshore conditions; coating maintenance cycles and replacement costs; stainless steel crevice corrosion in chloride environments; FRP corrosion resistance comparison in equivalent North Sea marine exposure].

Comments


bottom of page