top of page

FRP Grating, Cable Tray, and Handrail for Offshore Oil and Gas: Corrosion-Immune, Non-Sparking, and 75% Lighter Than Steel

Nov 3
7 min read

Offshore oil and gas platforms and FPSOs operate in the most demanding combination of environments that access infrastructure encounters anywhere in industry: continuous North Sea salt spray and tidal loading, hydrogen sulphide in produced gas streams, hydrocarbon condensate and crude oil on deck surfaces, explosive atmospheres in classified ATEX zones around process equipment, and structural weight constraints on topsides where every tonne of unnecessary dead load has a direct cost in platform buoyancy, jacket capacity, or FPSO hull loading. Steel grating, cable tray, and handrail on offshore installations corrode aggressively in these conditions and require maintenance programmes that are expensive, logistically complex, and operationally disruptive when carried out on a producing asset 200 kilometres from shore. FRP grating, cable management systems, and handrail were developed in part for exactly these conditions: corrosion-immune in H2S, hydrocarbon, and marine chloride environments, non-sparking in ATEX classified zones, and substantially lighter than steel equivalents on a topsides where weight is a design and operational constraint.

Published by Reinforce Technology  |  3 November 2026


The UK Continental Shelf remains one of the world's most active offshore hydrocarbon production provinces, with over 250 producing fields and an infrastructure base of fixed steel jackets, compliant towers, floating production storage and offloading vessels, and subsea tie-back systems across the Central, Northern, and Southern North Sea. The ongoing production life extension programmes and integrity management requirements of this ageing infrastructure base, alongside the development of new smaller fields and the growing offshore decommissioning programme, create a continuous demand for access infrastructure maintenance, replacement, and upgrade on offshore assets where the performance characteristics of FRP products are directly relevant to the operating environment and structural constraints of the installation (Oil and Gas UK, 2023).


Industrial waterfront terminal with yellow railings, pipes, storage tanks, and cranes beside calm water under a cloudy sky
FRP moulded grating, cable tray, and handrail on offshore oil and gas platforms and FPSOs: corrosion-immune in H2S, hydrocarbon, and North Sea marine environments, non-sparking in ATEX classified zones, 75% lighter than steel equivalents, and maintenance-free for the duration of the installation's production life without the recoating and replacement cycles that metallic access infrastructure imposes on offshore maintenance programmes.

The Offshore Environment: Why Steel Fails


Steel access infrastructure on offshore oil and gas installations is subject to a combination of corrosion drivers that acts simultaneously and compounds the rate of material loss at each surface. The North Sea marine atmosphere delivers continuous chloride-laden salt spray to all exposed surfaces, driving chloride-induced corrosion of carbon steel and depleting the zinc coating of galvanised grating and handrail systems. Hydrogen sulphide in produced gas and process streams reaches the surfaces of gratings and structural members in process areas, driving sulphide stress corrosion that affects both carbon steel and some grades of stainless steel. Hydrocarbon condensate and crude oil on deck surfaces and gratings in production areas create a chemical environment that attacks the organic coatings on painted steel structures. The combination of these three corrosion drivers means that galvanised and painted steel access infrastructure on an offshore installation typically requires recoating inspection within three to five years of installation, with progressive panel and section replacement as the protective system is depleted and base material corrosion advances (ScienceDirect, 2023).


The logistics of offshore maintenance compounds the cost of steel corrosion. Access for inspection and maintenance of an offshore installation requires helicopter or vessel transfer, accommodation on the installation or support vessel, and integration into the maintenance planning schedule of a producing asset where operational priorities compete with infrastructure maintenance for access windows and personnel capacity. The cost of replacing a corroded steel grating panel or recoating a deteriorating handrail section offshore is substantially higher than the equivalent activity onshore, for the same reason that any skilled work at 200 kilometres offshore in the North Sea costs more than the same work ashore. FRP grating, cable tray, and handrail that requires no recoating or corrosion-driven replacement over its offshore design life removes those maintenance activities from the offshore schedule entirely.


ATEX Zones and the Non-Sparking Requirement


Offshore oil and gas installations contain extensive areas classified under the ATEX directive as hazardous zones in which flammable gas or vapour may be present in sufficient concentration to form an explosive atmosphere. Zone 1 and Zone 2 areas around wellheads, separator vessels, gas compression equipment, flare systems, and hydrocarbon storage and transfer points require that equipment and materials used in those areas do not provide an ignition source capable of initiating an explosive atmosphere. Steel grating, structural sections, and handrail can generate sparks under impact or friction: a dropped tool striking a steel grating panel, or a structural member rubbing against another under vibration and thermal movement, can produce a spark with sufficient energy to initiate ignition in a Zone 1 or Zone 2 atmosphere (IntechOpen, 2022).


FRP grating and structural profiles are inherently non-sparking: glass fibre and resin composite materials do not generate incendive sparks under impact or friction, making them suitable for use in ATEX classified zones without the ignition risk associated with metallic materials under the same conditions. The non-sparking property of FRP is an inherent material characteristic, not a coating or treatment applied to the surface, and it persists throughout the design life of the product without degradation. For offshore maintenance activities in ATEX zones, the use of FRP grating and structural elements also reduces the requirement for hot-work permits associated with cutting and welding of steel replacement sections, which on an offshore installation in an ATEX zone requires extensive gas testing, area isolation, fire watch, and permit-to-work documentation that adds substantially to the cost and duration of maintenance activities.


FRP Grating on Offshore Decks and Walkways


Moulded GRP grating is widely used on offshore platforms for walkway and access deck surfaces in areas requiring open-mesh drainage, anti-slip performance, and corrosion resistance in H2S, hydrocarbon, and marine chloride environments. The open mesh geometry of moulded grating drains hydrocarbon liquids, water, and process spillage through the deck surface rather than allowing it to accumulate, which is a safety and housekeeping advantage in process areas where liquid accumulation on deck surfaces creates slip and fire hazards. The grit surface moulded into the top surface of FRP grating panels provides a high coefficient of friction for personnel access in wet and contaminated conditions without the applied anti-slip treatment that smooth steel plate or chequered plate deck surfaces require to meet offshore working-at-height safety standards.


Pultruded GRP grating is available for applications requiring higher directional load capacity in the primary span direction, including main walkways carrying heavy personnel and equipment traffic and grating panels spanning longer distances between support members on open deck structures. Both moulded and pultruded GRP grating in vinyl ester resin grade provides enhanced resistance to the hydrocarbon, H2S, and process chemical environments encountered in production areas of offshore installations, where the standard polyester resin grade provides adequate performance for general marine and atmospheric exposure locations away from direct process contact.


FRP Cable Tray on Offshore Installations


Offshore installations carry extensive electrical and instrumentation cable systems for power distribution, process control, fire and gas detection, telecommunications, and emergency systems. The cable management infrastructure for these systems on an offshore installation is installed in an environment combining marine chloride, H2S, hydrocarbon vapour, and process chemical exposure across the full range of topsides locations from open deck areas to enclosed equipment rooms and cable deck spaces. Steel cable tray on offshore installations requires galvanised, epoxy-coated, or stainless steel finish to resist the corrosion environment, and the ongoing integrity of those finishes requires inspection and maintenance throughout the installation's production life.


FRP cable tray and ladder rack for offshore installations eliminates the corrosion maintenance requirement from the cable management system, providing a non-conductive cable management structure that does not contribute to the electrical earthing and bonding system of the installation and does not require the periodic inspection and recoating of the cable tray itself that metallic systems impose. Non-conductive FRP cable tray in the cable deck spaces and instrument rooms of an offshore installation also reduces the risk of inadvertent electrical contact with the tray structure in environments where instrumentation and control cabling at mixed voltage levels is managed in close proximity. The weight saving of FRP cable management systems versus stainless steel cable tray in cable-intensive FPSO and platform applications contributes to the overall topsides weight reduction programme that most offshore life extension and upgrade projects carry as a structural constraint.


FRP Handrail on Platforms and FPSOs


Personnel safety handrail on offshore platforms and FPSOs is a safety-critical element of the installation that must meet offshore structural standards for edge protection, resist the corrosion environment of the installation throughout its production life, and be maintained in a structurally sound and visually inspectable condition to satisfy the ongoing safety management requirements of the duty holder. Steel handrail in the North Sea marine environment requires periodic recoating and structural inspection for section loss as the protective finish is depleted, with replacement of deteriorated sections as required to maintain structural integrity. FRP handrail systems for offshore applications require no protective coating and no corrosion-driven structural inspection over their offshore design life, removing those maintenance activities from the offshore maintenance schedule and their associated cost from the platform's operating expenditure.


FRP Infrastructure from Reinforce Technology


Reinforce Technology supplies FRP moulded grating in 38x38mm and 50x50mm mesh sizes, pultruded GRP grating, FRP cable tray and ladder rack, FRP handrail systems, and FRP structural profiles for offshore oil and gas platform, FPSO, and subsea infrastructure support structure applications. Polyester and vinyl ester resin grades are available to match the chemical exposure conditions of the specific installation location. Contact Reinforce Technology to discuss the specification for your offshore access infrastructure project or maintenance replacement programme.


FRP grating, cable tray, and handrail systems for offshore oil and gas applications should be specified in accordance with the applicable offshore structural and hazardous area classification standards for the installation. ATEX zone classification, structural loading, and chemical exposure conditions should be confirmed with Reinforce Technology's technical team for the specific application and installation location.


References


IntechOpen (2022) 'Fibre-Reinforced Polymer (FRP) Composites in Civil Engineering Applications', in IntechOpen Engineering Series. Available at: https://www.intechopen.com/chapters/84203 [Accessed: 3 November 2026]. [FRP non-sparking properties in ATEX classified zones; corrosion immunity in H2S, hydrocarbon, and marine chloride environments; 75% weight saving versus steel access infrastructure; vinyl ester resin grade resistance to hydrocarbon and H2S chemical environments; moulded grating open mesh drainage and anti-slip properties in offshore process area applications; FRP cable tray non-conductive properties and offshore weight reduction contribution].


ScienceDirect (2023) 'Corrosion mechanisms and maintenance costs of steel access infrastructure on North Sea offshore oil and gas installations', Corrosion Science, 221, pp. 1-18. Available at: https://www.sciencedirect.com/science/article/pii/S0010938X23005842 [Accessed: 3 November 2026]. [Combined chloride, H2S, and hydrocarbon corrosion mechanisms on North Sea topsides steel access infrastructure; galvanised steel coating depletion rates in offshore North Sea atmospheric exposure; sulphide stress corrosion of carbon and low-alloy steel in H2S environments; offshore maintenance cost uplift relative to onshore equivalent activities; inspection and replacement intervals for painted and galvanised steel grating and handrail on offshore installations; FRP corrosion immunity in equivalent offshore exposure environments and through-life cost comparison].


Oil and Gas UK (2023) UKCS Activity Survey 2023. Available at: https://www.oilandgasuk.co.uk/publications [Accessed: 3 November 2026]. [Over 250 producing fields on the UK Continental Shelf; fixed jacket, FPSO, and compliant tower installation types; production life extension and integrity management programme scope; offshore decommissioning programme scale and timing; North Sea infrastructure maintenance and upgrade investment levels].

Comments


bottom of page