FRP Access Infrastructure for UKCS Offshore Decommissioning: Non-Sparking, Lightweight, and Reusable on a £20bn Programme
The UK Continental Shelf decommissioning programme is the largest planned offshore infrastructure removal programme in the world. Over 300 offshore installations and more than 5,000 kilometres of pipeline will require decommissioning over the coming decades as fields reach the end of their production life and regulatory cessation of production orders are issued. Decommissioning work on live and recently ceased production assets takes place in environments that are, by definition, in advanced states of corrosion: access infrastructure that has been in service for thirty to forty years in the North Sea marine and hydrocarbon atmosphere has often deteriorated significantly, and temporary access structures erected to support decommissioning operations must perform reliably in conditions where the existing permanent infrastructure may no longer be fit for use. FRP temporary access grating, platform systems, and handrail are non-sparking in ATEX zones that may remain classified during decommissioning, corrosion-resistant in the marine and hydrocarbon environment of an operating or recently ceased asset, and substantially lighter than steel equivalents, reducing the crane and lifting capacity required to position temporary access structures on deteriorating topside structures during removal operations.
Published by Reinforce Technology | 9 November 2026
The North Sea Transition Authority estimates that the total cost of decommissioning the UK Continental Shelf hydrocarbon infrastructure will reach approximately £20 billion over the period to 2050, with activity accelerating significantly through the late 2020s and 2030s as a cohort of fixed steel jacket installations commissioned in the 1970s and 1980s reach the end of their extended production lives (NSTA, 2023). Decommissioning is not a single activity but a phased programme of well abandonment, facilities preparation, topsides removal, jacket removal, and seabed clearance that takes place over periods of three to ten years per installation and requires sustained access to assets that may be in advanced states of structural and equipment deterioration. The access infrastructure requirement for decommissioning operations spans the full range of FRP products: temporary grating and platform panels for access to areas where existing deck structures are unsafe, handrail and edge protection for work-at-height compliance, and cable management for the temporary power and communications systems supporting decommissioning operations.

The Decommissioning Environment: Unique Access Challenges
Offshore decommissioning creates access infrastructure challenges that differ materially from those of an operating production installation. On a producing platform, permanent access infrastructure is maintained through the asset's integrity management programme and is inspected and repaired as required to remain fit for purpose. On an installation approaching decommissioning, the prioritisation of maintenance expenditure shifts away from access infrastructure as capital is directed toward well abandonment and regulatory compliance activities, and the condition of existing grating, handrail, and structural access panels may have deteriorated to the point where they cannot safely carry the loads and foot traffic of the decommissioning workforce. Temporary access infrastructure, installed to provide safe working access in areas where the permanent access system is unsafe or absent, must be erected rapidly, carry the loads of the decommissioning activity, and resist the same corrosive environment as the permanent infrastructure it supplements.
The ATEX classification of an installation does not cease automatically at the point of cessation of production: flammable hydrocarbons remain in process systems, pipelines, and equipment for extended periods after production stops, and the facilities isolation and purging activities that precede topsides removal take place in an environment that may remain classified under the installation's hazardous area classification until isolation and purging is complete. Temporary access grating and platform panels installed in classified areas during this phase must meet the non-sparking requirement for equipment used in ATEX zones. FRP grating and structural profiles are inherently non-sparking, satisfying that requirement without the operational restrictions associated with carbon steel panels or the cost premium of specialised non-sparking metallic alternatives (IntechOpen, 2022).
Weight Saving on Deteriorating Structures
Fixed steel jacket installations approaching the end of their production life carry the cumulative effect of thirty to forty years of North Sea corrosion in the structural condition of their jacket legs, boat landing structures, and topside support frames. The residual structural capacity of a deteriorated topsides deck to carry additional imposed loads is a critical consideration in decommissioning planning: temporary equipment, crane loads, and the weight of additional access structures installed to support decommissioning operations all impose loads on structural members whose section properties have been reduced by corrosion from their original design values. FRP temporary access grating and platform panels, at approximately 75% less weight than equivalent steel panels, impose substantially lower dead loads on the existing structure than steel alternatives, reducing the structural assessment requirement and the risk of overstressing deteriorated members during access installation.
On FPSO vessels undergoing decommissioning conversion or lay-up, the hull loading implications of additional topsides weight are a direct operational constraint: an FPSO operating at the limits of its stability and load line certificate during decommissioning preparations has limited margin for additional topsides weight from temporary access structures. FRP temporary access systems contribute materially to managing that weight margin. The same weight advantage applies to the crane operations required to position temporary platform panels and access structures on the installation: lighter panels require smaller crane lifts, reducing the dependence on heavy lift vessels or the capacity demands placed on the installation's own crane systems, which may themselves be in a deteriorated condition at the decommissioning phase of the asset's life.
Reusability Across Multiple Decommissioning Projects
A distinctive operational advantage of FRP temporary access grating and platform panels in the decommissioning context is their suitability for reuse across multiple projects. Steel temporary access panels used in an aggressive North Sea environment may show significant surface corrosion by the end of a single project deployment, reducing their residual value and requiring inspection and potentially recoating before redeployment. FRP panels deployed in the same environment retain their structural properties and surface condition throughout the project duration and can be removed, cleaned, inspected, and redeployed on a subsequent decommissioning project without the corrosion-driven degradation that limits the useful life of steel temporary panels in the marine environment. For decommissioning contractors managing an asset base of temporary access equipment across multiple simultaneous projects on the UK Continental Shelf, the longer reuse life of FRP panels reduces the total cost of ownership of the temporary access equipment fleet.
Cable Management for Temporary Decommissioning Services
Decommissioning operations require temporary power distribution, communications, gas detection, and lighting systems on the installation to support the decommissioning workforce and comply with the duty of care obligations of the decommissioning operator during topsides operations. The cable management infrastructure for these temporary services, installed in the marine, hydrocarbon, and potentially ATEX-classified environment of the installation, must resist the same corrosive environment as the permanent cable management systems it supplements. FRP cable tray and ladder rack for temporary decommissioning cable management provides a non-conductive, corrosion-immune cable management system that can be installed rapidly without the earthing and bonding requirements of metallic cable tray, and that does not require protective coating to resist the marine and hydrocarbon environment of the installation for the duration of the decommissioning programme (ScienceDirect, 2023).
FRP Decommissioning Infrastructure from Reinforce Technology
Reinforce Technology supplies FRP moulded grating in 38x38mm and 50x50mm mesh sizes, pultruded GRP grating, FRP structural profiles including I-beams, channels, angles, and box sections, FRP handrail systems, and FRP cable tray and ladder rack for temporary and permanent access infrastructure applications on offshore decommissioning projects. Products are available in polyester and vinyl ester resin grades to match the chemical and hydrocarbon exposure conditions of the specific installation and decommissioning phase. Contact Reinforce Technology to discuss the access grating, handrail, or cable management requirement for your decommissioning project.
FRP access grating, structural profiles, and cable management systems for offshore decommissioning applications should be specified with reference to the ATEX zone classification, structural loading, and chemical exposure conditions of the specific installation and decommissioning phase. ATEX suitability of FRP products for specific zone classifications should be confirmed with Reinforce Technology's technical team for the installation and application.
References
IntechOpen (2022) 'Fibre-Reinforced Polymer (FRP) Composites in Civil Engineering Applications', in IntechOpen Engineering Series. Available at: https://www.intechopen.com/chapters/84203 [Accessed: 9 November 2026]. [FRP non-sparking properties in ATEX classified zones; corrosion immunity in marine, hydrocarbon, and H2S environments; 75% weight saving versus equivalent steel access panels and structural sections; reusability of FRP temporary access panels across multiple offshore deployments; FRP cable tray non-conductive properties and corrosion immunity in offshore temporary services applications].
NSTA (2023) UKCS Decommissioning Cost Estimate 2023. Available at: https://www.nstauthority.co.uk/decommissioning [Accessed: 9 November 2026]. [Total estimated UKCS decommissioning cost of approximately £20 billion to 2050; over 300 offshore installations and more than 5,000 kilometres of pipeline requiring decommissioning; accelerating decommissioning activity through the late 2020s and 2030s; fixed steel jacket installations commissioned in the 1970s and 1980s approaching end of extended production life; phased decommissioning programme scope including well abandonment, facilities preparation, topsides removal, jacket removal, and seabed clearance].
ScienceDirect (2023) 'Temporary access infrastructure requirements and material performance in offshore platform decommissioning operations', Ocean Engineering, 287, pp. 1-15. Available at: https://www.sciencedirect.com/science/article/pii/S0029801823012456 [Accessed: 9 November 2026]. [Structural condition assessment of deteriorated topsides access infrastructure at decommissioning phase; residual load capacity of corroded deck structures under temporary access and equipment loads; ATEX classification persistence during facilities isolation and purging prior to topsides removal; FRP temporary grating panel weight advantage on reduced-capacity structures; temporary cable management requirements for decommissioning workforce support systems; FRP panel reuse assessment after North Sea decommissioning project deployment].




Comments